Home › FAQ

Frequently asked questions about hemp blocks

Composition, installation, price, regulations, maintenance: everything you need to know before you get started.

Renovated room: walls insulated with hemp blocks and finished in lime plaster

These answers are deliberately short. Our in-depth articles cover each topic in detail.

Frequently asked questions

Hemp blocks in 14 questions

What is a hemp block?

A hemp block is precast hempcrete: 84% hemp shiv, the woody core of the hemp stalk, bound with Vicat prompt natural cement and factory-moulded in a 60 × 30 cm format. Delivered ready to lay, it is built with thin joints and combines insulation, thermal mass and humidity regulation.

Is a hemp block wall load-bearing?

No. BIOSYS and MULTICHANVRE blocks are not load-bearing: they are always combined with a load-bearing structure (post-and-beam, backing wall, timber frame, etc.).

Can you build a house from hemp?

Yes, with a load-bearing structure. In new builds, MULTICHANVRE blocks fill a timber frame, while the BIOSYS system acts as insulating permanent formwork and infill for a reinforced concrete post-and-beam frame. In renovation, the blocks insulate from the inside or the outside.

Which thickness and thermal resistance should I choose?

Four thicknesses: 10 cm (R 1.5), 15 cm (R 2.3), 20 cm (R 3.0) and 30 cm (R 4.6 m².K/W, dry values). The 10 cm block is mainly used for internal and external wall insulation (IWI and EWI); for floors and partition walls, thicker blocks are preferred. The MULTICHANVRE simulator will guide you.

How much does a hemp block cost per m²?

As a guide, typical public prices seen at builders’ merchants start at €35/m² incl. VAT in 10 cm, €51/m² in 15 cm, €66/m² in 20 cm and €95/m² in 30 cm. The price of your project depends on the surface area, the thickness and the accessories: request a quote.

Is the hemp block suitable for RE2020?

Hemp captures a large amount of carbon as it grows, and that carbon stays locked in the block. Our FDES (French environmental product declarations: BCE 30 cm, BCD 20 and 30 cm) are verified under the INIES programme: these are what go into a project’s RE2020 (France’s environmental building regulation) calculation.

Which finishing renders and plasters are compatible?

Indoors: spray plaster, lime, clay or plasterboard. Outdoors: a lime render with full mesh reinforcement. Application follows the render manufacturer’s specifications.

Do I need a vapour barrier?

For standard walls, no: hempcrete regulates humidity, provided the wall keeps at least one face open to moisture and vapour transfer. On an existing wall that is sealed on the other side, for example with a cement render, feasibility must be checked by a study. In wet rooms, areas exposed to splashing must be protected, for example with a plasterboard lining that meets wet-room requirements.

Does it resist fire and rodents?

The block is rated B-s1,d0 for reaction to fire, and the BIOSYS system achieves EI 90 fire resistance. It is naturally resistant to rodents, pests and mould. It is not rot-proof, however: store pallets under cover, in a dry place, and never stack them.

How are hemp blocks installed?

MULTICHANVRE goes up in three stages. The first course sits on a bed of water-repellent mortar about 2 cm thick, which stops rising damp and levels the base. The blocks are then laid with M.B.M. mortar using a notched trowel, with thin joints of about 3 mm and staggered joints (an overlap of at least one third of a block, i.e. 20 to 40 cm), and tied to the backing wall with brackets, strips of steel strapping or rosettes (2 to 5 per m²). Finally comes the render or plaster. For EWI, the first course sits at least 15 cm above outside ground level. BIOSYS blocks, on the other hand, interlock dry, with no adhesive or mortar.

How do I fix a heavy load to a hemp wall?

On 20 and 30 cm MULTICHANVRE blocks: up to 10 kg per fixing, a VBA 6 × 100 screw with no pilot hole; up to 30 kg, a chemical anchor with an M8 threaded rod. Beyond that (wall cabinet, water heater, wall-hung sanitaryware), the fixing passes through the block and bears on the backing wall or on an added support structure. The 10 and 15 cm blocks must not carry loads directly.

How do I run electrics?

Cut chases with a wall chaser and holes with a hole saw, fix the conduits and back boxes, then fill with a small batch of hempcrete or a filler compatible with the render or plaster. For internal insulation, services can also run in the gap left between the existing wall and the lining.

Where can I buy hemp blocks, and how long does delivery take?

Our blocks are sold through our network of partner builders’ merchants throughout France. Blocks and standard accessories are kept in stock: allow one week for delivery on average, longer during the winter and summer holidays. Tell us about your project and we will point you in the right direction within 48 working hours.

How long does a hempcrete wall last?

Hempcrete has been used in France since the 1980s, with very few documented problems; our own reference projects date back to 2017. Protected by its render or plaster and installed correctly, it needs no particular maintenance beyond that of its finish. Outdoors, roof overhangs and sills protect the wall from rain.

Can’t find your answer?

Ask your question